Skip to content
Mikrografika
← Articles

Drums · 8 min read

Recording drums that sound vintage today: damping, room and mics

Dead, thuddy, warm drums start before the mixer: tuning, tea towels, the right room and just two or three mics. A practical guide for home studios.

By Daniel ·

You can get a long way towards a vintage drum sound in the mix. But if you can record the drums yourself, the biggest gains happen before anything hits the computer. The kit, the room and two or three well-placed mics matter more than any plug-in, mine included.

Broadly, there are two classic flavours. Early-to-mid 60s drums are often roomy and ringy, captured with few mics. Late-60s and 70s drums go the other way: dead, dry and thuddy, with towels on the snare. Decide which one you want before you start, because the choices pull in opposite directions.

The kit

Heads

  • Coated heads on the snare and toms give a warmer, softer attack than clear heads.
  • Single-ply heads ring more and sound more open. Two-ply heads sound fatter and shorter.
  • Calf-skin or calf-style heads give the most authentic old tone: dark, woody, with very little overtone. They react to humidity, so tune them on the day.

Tuning

  • For the open 60s sound: tune toms and snare medium-high, so they sing a clear note.
  • For the dead 70s sound: tune lower, just above where the head goes floppy and loses its note.
  • Tune the kick low and loose, with the front head on. Many old kits had no hole in the front head.

Damping

This is where the 70s sound comes from.

  • Tea towel on the snare: fold a cotton tea towel and lay it over part of the snare head. Tape one edge down. Move it until the ring is gone but the crack is still there.
  • Tape and tissue: a strip of gaffer tape with a folded tissue under it, near the edge of a tom, kills overtones without killing the note.
  • Kick: a small pillow or blanket inside the drum, just touching the batter head.
  • Wallet trick: a wallet or small notebook resting on the snare edge is quick and surprisingly effective.

Play a few hits after each change. Go too far and the kit sounds like cardboard.

The room

  • For roomy 60s drums: a medium-sized room with hard surfaces, but not a long, slappy echo. A wooden-floored living room can be great.
  • For dead 70s drums: a small, soft room. Hang duvets, put the kit on a rug, stack cushions in the corners.

Clap your hands in the middle of the room. A short, even decay is good. A metallic ring or a fluttering echo means you need more soft things on the walls.

The mics

The fewer mics, the more vintage it tends to sound, because there's less phase smear between them and the kit sounds like one instrument.

One mic

Put one mic about a metre in front of the kit, at roughly chest height, pointing at the snare. Move it closer to the kick for more low end, higher for more cymbals. It's how a lot of early records were made, and it's a great test of how good your kit and room sound.

Two or three mics

The classic small setup:

  1. Overhead: one mic above the kit, about a metre above the snare, or one over the drummer's right shoulder looking down at the snare.
  2. Kick: a dynamic mic a few centimetres outside the front head, or inside the drum for more thud.
  3. Snare (optional): a dynamic mic a few centimetres above the rim, angled at the centre.

Measure the overhead's distance to the snare and keep it the same if you move things. That keeps the snare from sounding hollow when the mics are combined.

Which mics

If you have a ribbon mic, try it as the overhead. It takes the edge off cymbals and gives the whole kit a dark, warm picture. Any dynamic mic you already own will do for kick and snare.

Record to commit

Old records sound decided. The drums were balanced on the way in, often to one or two tracks.

  • Set your levels so the drums peak around -12 to -6 dBFS. Leave headroom.
  • Try recording through a little compression and saturation on the way in, if your interface or monitoring allows it.
  • Then bounce the drum mics to a single stereo or mono track early in the mix, and work with that.

Finish in the mix

Once the sound is right at the source, mixing is easy:

  • Compress the drum bus with a medium attack and fast release, 3 to 6 dB.
  • Add tape-style saturation and a gentle top roll-off from 10 to 12 kHz.
  • Keep the image narrow.

On my own drum recordings this is where Ember Press goes: on the drum bus, Drive around 5, Speed fast, Low-End Weight on Bump. It does the bus compression and the tape step together.

Try this

  1. Choose: open 60s or dead 70s.
  2. Coated heads, tuned to suit, with towels and tape for the dead sound.
  3. Treat or open up the room to match.
  4. Start with one mic. Add kick and snare only if you need them.
  5. Commit: bounce the kit to one track early.
  6. Compress, saturate and narrow on the bus.