Skip to content
Mikrografika
← Articles

Drums · 7 min read

60s drums and saturation: what the old desks added

Valve desks, transformers, tape and four tracks: what each one did to drums in the 1960s, and how to rebuild that warm, dense sound with modern tools.

By Daniel ·

Modern drum recordings are clean. Every hit has a sharp front edge, the kick goes down to the floor, the cymbals sparkle forever. Play a 1960s drum track next to one and the old one sounds smaller on paper, yet it often feels better: rounder, thicker, more like a band in a room.

The difference is mostly what happened between the drums and the record. Every stage added a little colour, and drums, with their sharp peaks, are the instrument that shows it most.

The desk: valves and transformers

Most mixing desks of the early and mid 60s used valves (vacuum tubes) and had transformers on their inputs and outputs; transistor desks took over as the decade went on. Neither is perfectly clean.

  • Valves add mostly even harmonics when pushed: extra tones an octave and an octave-and-a-fifth above the note. To the ear that reads as warmth and fullness.
  • Transformers soften the very fastest peaks and add a little weight in the low end, especially when driven hard.

On drums this shaves the spiky front off each hit and gives the body of the drum more say. The snare gets fatter. The kick gets more "thud" and less "click".

Tape: the soft ceiling

Tape doesn't clip like digital. As you push it, it squashes peaks more and more gently, adding harmonics as it goes. Engineers knew this and often recorded drums hot on purpose.

Tape also:

  • Lifts a band of low frequencies a little (the "head bump", usually somewhere between 40 and 120 Hz depending on speed).
  • Rolls off some of the very top, especially at slower speeds or after a few generations of copying.
  • Adds faint hiss, which glues quiet parts together more than you'd think.

Four tracks, and a lot of bouncing

Early in the decade many sessions had three or four tracks to work with, though it varied a lot by studio and year. Drums often went to one track, sometimes shared with bass or more. When tracks ran out, engineers mixed several down to one and carried on: a "bounce".

Each bounce was another trip through the desk and onto tape, so the drums picked up more saturation and lost a little more top each time. It also meant the drum balance was decided early and could not be changed later. You committed.

Bleed and mono

With the band in one room, the drum mics heard everything and every other mic heard the drums. That spill (or "bleed") sounds messy in isolation but makes the kit feel like part of the room and the band. Most of these records were also mixed for mono, so the drums were a single, solid image rather than spread wide.

Rebuilding it today

You can't buy back the room, but you can rebuild the chain. Work on a drum bus (all drum tracks sent to one channel) so the colour hits the whole kit at once, the way it would have on one track of tape.

1. Narrow it

  • Pan your drums much narrower than usual, or sum the drum bus to mono.
  • Kick, snare and toms in the middle, overheads only slightly apart.

2. Saturate in stages

Several gentle stages sound more natural than one heavy one.

  • Stage one, the desk: a valve-style saturation, set so you hear the snare thicken but not crackle.
  • Stage two, the tape: a tape-style saturation, pushed until the peaks start to round off. Watch the transient shape on your meter if you can: the spikes should get shorter.
  • Match levels after each one. Saturation makes things louder, and louder always sounds better at first.

3. Compress the bus

A bus compressor with a medium attack (10 to 30 ms) lets the front of each hit through, then clamps the body. A fast release around 50 to 150 ms brings the room and ring back up between hits. Aim for 3 to 6 dB of reduction on the loudest hits.

4. Shape the ends

  • Gentle low-pass filter starting around 10 to 12 kHz.
  • High-pass around 30 to 40 Hz to clear sub rumble that 60s gear would never have recorded.
  • A small lift of 1 to 2 dB somewhere around 60 to 100 Hz to imitate the tape bump.

Doing it in one move

This chain is exactly why I built Ember Press. Drive pushes into a two-stage compressor, then tube and tape saturation, with make-up gain so the level stays even while you listen. Low-End Weight adds the bump, and above Drive 6 the top end eases down the way a hot tape would. On a drum bus, start around Drive 5 with a fast Speed and go from there.

Try this

  1. Send all drums to one bus and narrow the image.
  2. Add a valve-style saturation, then a tape-style one, both gentle.
  3. Level-match after each stage.
  4. Bus compress: medium attack, fast release, 3 to 6 dB.
  5. Low-pass around 10 to 12 kHz, high-pass around 35 Hz, small lift at 60 to 100 Hz.
  6. Bounce the result to audio and add one more light pass of saturation. Commit, like they had to.